Lure Machines
& Drive Wheels
Reversible Lure
Machine
This lure machine is not for everyone, but there is simply no
better way to play train puppies or retrain the experienced hound that is now
anticipating and cutting the course. This 12 volt motor runs at the same speed
and torque in both directions of operation and has two ball bearings (front and
rear) installed. You can quickly and conveniently reverse direction of the lure
using the handheld control box. The lure machine is constructed of black high
density plastic and includes, a voltmeter, a safety switch,
eight inch spikes and a control box with 25 foot cord. (wt. 35 lbs.).................$890.00
New 12 volt reversible motor sold only as replacement for Injoy lure
machines. It is of new manufacture and has two ball
bearings installed (front and rear) with a one piece 5/8" diameter shaft.
(wt. 24 lbs.).................$400.00
STD Lure Machine
With a New TB1225 Motor
The stand is constructed of 1/2” black high density plastic (need new
picture) and
supplied complete with our "new" 12 volt
TB1225 motor (2.5 hp), with solenoid, two battery cables, voltmeter, 8” spikes and a
switch with 15’ cord. This motor is being exclusively manufactured
for Injoy and has four field coils (the Ford starter motor has two) and ball
bearings front and rear. This machine should be used by clubs and
individuals that run lots of dogs. See below for more
info on this motor. (wt. 34 lbs.)................$485.00
With a New TB1248 Motor
The stand is constructed of 1/2” black high density plastic (need new
picture) and
supplied complete with our "new" 12 volt
TB1248 motor (4.8 hp), with solenoid, two battery cables, voltmeter, 8” spikes and a
switch with 15’ cord. This motor is being exclusively manufactured
for Injoy and has four field coils (the Ford starter motor has two) and ball
bearings front and rear. This machine should be used by clubs and
individuals that run lots of dogs and/or long courses. See below for more
info on this motor. (wt. 34 lbs.)................$550.00
TB1225 Motor
This
12 volt motor produces 2.5 HP (approx. the same as the Ford starter motor) and is being manufactured to Injoy specifications.
It is designed to
provide a more reliable and durable choice when compared with the Ford starter
motor. The motor has a four hole mounting plate with a six inch long, 5/8 inch
diameter shaft. To provide more torque, it has four field coils (the Ford
Starter has two) and the shaft turns on two ball bearings. This is a high
quality motor manufactured with lure coursing requirements and performance in
mind. (wt. 22 lbs.).........................$290.00
TB1248 Motor
From the outside, this 12 volt motor looks like the TB1225 but on the
inside, the components produce 4.8 HP. The motor has the same shaft and
ball bearings as the TB1225. This motor has almost twice the HP of the
Ford starter motor and should be used with caution. (wt. 23 lbs.).........................$350.00
S/S Continuous Loop
Wheel
A new and improved hub design now allows the wheel to be
installed at the end of the motor shaft using the supplied
through bolt or moved in closer to the lure stand and fixed in
place using a set screw onto a flat spot on the motor shaft.
This is a “pie pan” style wheel and is constructed
of custom spun stainless steel sides. The geometry of the string
groove is such that it will perform well with a minimum amount of
line tension (8 to 12 lbs.). The wheel is recommended for clubs
holding trials in all weather conditions and individuals who
simply
wants to use the very best.
(wt. 4 lbs.)............$190.00
Operating instructions for the S-S
Continuous Loop Wheel.
STD Take Up Wheel
A 12 inch diameter wheel with a solid 4 inch diameter core that will hold approximately 1200 yards of line.
The wheel is constructed of a high density plastic which is, at least, twice as
strong as hardwood plywood. This
wheel can be used for sighthound racing or a drag lure coursing setup and to
retrieve your string for storage after using a continuous loop system. (wt. 7
lbs.)......$100.00
JRT Racing Take Up Wheel
This wheel is intended for Jack Russell Terrier straight racing and is
constructed of high grade aluminum with 7 inch diameter side plates and a 2 inch
diameter core with a 3-1/2 inch width between side plates. The 2 inch core will give a lure speed of approximately one half
that given by the STD Take Up Wheel. Many of my JRT customers have
requested a slower lure speed for their straight racing events and this wheel is
designed specifically for this purpose.
(wt. 3
lbs.)................$120.00
This lure machine is not for everyone, but there is simply no
better way to play train puppies or retrain the experienced hound that is now
anticipating and cutting the course. This 12 volt motor runs at the same speed
and torque in both directions of operation and has two ball bearings (front and
rear) installed. You can quickly and conveniently reverse direction of the lure
using the handheld control box. The lure machine is constructed of black high
density plastic and includes, a voltmeter, a safety switch,
eight inch spikes and a control box with 25 foot cord. (wt. 35 lbs.).................$890.00 
This
12 volt motor produces 2.5 HP (approx. the same as the Ford starter motor) and is being manufactured to Injoy specifications.
It is designed to
provide a more reliable and durable choice when compared with the Ford starter
motor. The motor has a four hole mounting plate with a six inch long, 5/8 inch
diameter shaft. To provide more torque, it has four field coils (the Ford
Starter has two) and the shaft turns on two ball bearings. This is a high
quality motor manufactured with lure coursing requirements and performance in
mind. (wt. 22 lbs.).........................$290.00
Products